Hélico

Nouveaux produits

Promotions

Déjà vus

Nouveau CopterX (CX-3X900) Flybarless 3 Axis Gyro System Agrandir l'image

CopterX (CX-3X900) Flybarless 3 Axis Gyro System

CX-3X900

Neuf

Système flybarless CopterX complet

Plus de détails

60,00 €

En savoir plus

CopterX (CX-3X900) Flybarless 3 Axis Gyro System

CX-3X900 Features:

  • High quality MEMS sensors on three axes
  • Digital signal processor with extremely high arithmetic performance
  • Axis-corrected sensor system prevents influences of individual functions
  • Integrated digital Cyclic Ring function
  • Accurate localization and excellent ability to prevent crosswind
  • Integrated mechanical, 90°, 120°, 135° and 140° swashplate mixer
  • Dynamic swashplate turn for optimal position stability while pirouetting the helicopter
  • Suitable for two and multi-blade rotor heads
  • Swashplate servo and rudder servo works fine with all common digital servo and analog servo
  • Digital servo with 1520uS and 760uS
  • You can update your configurations by the FBL Programmer. cause CX-3X900 setup very easy

CX-3X900 Specification:

  • MEMS Gyro Sensors in three Axes
  • Digital signal processor
  • Operating voltage: 4-10 Volts, current
  • Temperature range: -10°C to +50°C
  • Weight: 15g
  • Servo compatibility: 1520uS and 760uS digital servos, Analog servo
  • Spare parts: foam and double-side adhesive tape and Stainless steel plate and terminated line
  • Dimensions: 33*34*18mm

CX-3X900 Suggestion of CX-3X900 setup procedures:

  • When installing CX-3X900 on your heli for the first time, the rudder stick must be pushed to the left end or right end within 3 seconds after power on. Then CX-3X900 enters into initial setup mode
  • Check whether the direction of swash plate servos(AILERON, ELEVATOR, PITCH servos)correct or not. If not correct, you can adjust direction of AILERON or ELEVATOR or PITCH servo in TX REVERSE menu, until the direction of swash plate servos is correct
  • The swash plate of heli is at the neutral point. You must calibrate the neutral point of TX aileron/elevator/pitch servos through TX CALIBRATION/SWPL TRIM CALIBR in program box. So that the heli can fly more stabilized and have better anti-wind capacity. CX-3X900 can analyze swash plate mix signal from TX correctly

    Note: If you alter AILERON/ELEVATOR/PITCH sub trim in TX, you must calibrate the neutral point of swash plate through TX CALIBRATION/SWPL TRIM CALIBR in program box. Otherwise, heli will fly unstably and have weak anti-wind capacity
     
  • The swash plate of heli is at low level; calibrate the lowest point of TX aileron/elevator/pitch servos through TX CALIBRATION/SWPL LOW CALIBR in the program box. In this way, aileron/elevator/pitch servos can be synchronized
  • The swash plate of heli is at highest level; calibrate the highest point of TX aileron/elevator/pitch servos through TX CALIBRATION/SWPL HIGH CALIBR in the program box. In this way, aileron/elevator/pitch servos can be synchronized
  • If heli wobbling around and having weak wind capacity in flight, you can increase aileron gain. If heli vibrating, you can reduce aileron gain
  • If the heli raising head in flight, you can increase elevator gain; If heli lowering head in flight, you can reduce elevator gain
  • TX gain setup.
     
    Sensitivity pulse width Flight mode
    Gain 1940us 0
    1640us 1
    1740us 2
    1840us 3
  • When GN-MODE in the program box being at the current menu, alter TX gain, press function key F+and F- to refresh gain pulse instead of real time refreshing gain pulse. Gain pulse can also be refreshed at the time of changing flight mode

Avis

Aucun avis n'a été publié pour le moment.

Donnez votre avis

CopterX (CX-3X900) Flybarless 3 Axis Gyro System

CopterX (CX-3X900) Flybarless 3 Axis Gyro System

Système flybarless CopterX complet